LCD PROJECTOR LENS
MODEL NO. LNS-W04/LNS-W05/LNS-W06/LNS-W07
LENS INSTALLATION
AND REPLACEMENT PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet. Before installing or replacing the lens, make sure the type of cabinet of your
projector and install the lens following this procedure precisely.
When installing or replacing the lens, make sure the Lens Model No. matches with to
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens
Model No.
TYPE OF THE CABINET AND INSTALLATION PROCEDURES
This manual provides the following cabinet type models.
※ For lens installation to the other models than below, contact your sales dealer.
Printed in Japan
1AA6P1P4885-- (IDZC)
LENS REPLACEMENT AND INSTALLATION PROCEDURE
A
Disconnect the power cord from AC outlet.
Remove 5 screws (A) from the front cabinet.
Pulling up the front cover and remove it. (See Fig-1.)
1
A
A
Front Cover
Fig-1
Light Block Sheet Holder
Pulling up Light Block Sheet Holder and Cover Plate,
remove them. (See Fig-2)
2
Fig-2
Cover Plate
Remove the cover plate from the light block sheet
holder . (See Fig-3)
Cover Plate
3
Fig-3
-2-
Remove lens cap on the rear (mounting side) of the projection lens and mount Lens Attachment to the
lens with four screws included with the lens.
Insert the connector at the end of Lens Motor Lead into the socket located at right-top of the lens
attachment. (With motor model only.)
4
Note : Lens attachment is not included in this lens.
Lens Attachment
POA-LNA-04 (610 317 1289)
Lens Attachment
Socket
Connector
Locate motor on
right side.
Lens Motor Lead
Fig-4
Driver included with
the lens
Part No. (610 275 6029)
Lens Attachment
Driver included with
the lens
Part No. (610 275 6029)
Note : Lens Illustrations in this manual may differ from the actual product.
Pinch Lens Lock Lever and turn it clockwise to unlock. (See Fig-5.)
5
Insert the Lens through the lens mounting bracket and turn the lens lock lever anticlockwise until the lens
is securely mounted. After installing the lens, make sure the Lens is not loose and properly mounted.
(See Fig-6 and Fig-7 on next page.)
Lens Lock Lever
Fig-5
-3-
Release Lens Lock (C lockw ise)
Pinch the tab and
turn the lever
clockwise to unlock
the lens.
Fig-6
Fix Lens Lock (A nticlockw ise)
Pinch the tab and
turn the lever anti-
clockwise to lock
the lens.
Fig-7
CAUTION:
Turn the Lens Lock Lever anticlockwise until the lens is locked. Make sure
the lens is securely installed after installation.
FOCUS ADJUSTMENT (For Model LNS-W07)
Set up the projector and project image on the screen.
1. Loosen the Focus Lock Screw on the projection
lens.
2. Rotate the projection lens to obtain proper focus
on center area of the screen.
3. Lock the Focus Lock Screw securely.
When proper focus is not observed at outer area of
the screen, proceed following adjustments.
4. Loosen the Focus Lock Ring on the projection
lens. (Turn the Lock Ring counter-clockwise.)
5. Rotate the lens to obtain proper focus on outer
Focus Lock Ring
area of the screen.
6. Lock the Focus Lock Ring securely. (Turn the Lock
Ring to clockwise.)
Focus Lock Screw
If proper focus is not observed over the entire screen,
repeat above adjustments 1~ 6.
-4-
Install Light Block Sheet and Light Block Sheet Holder corresponding to the lens into the projector. (See Fig-8 and
Fig-9.) Appropriate light block sheet varies depending on the Lens Model No. Check Type No. on the light block
sheet and Lens Model No. and use an appropriate one.
6
Note: Make sure the light block sheet is fully inserted into the light block sheet holder when installing the
light block sheet and the sheet holder into the projector. Improper installation may cause the lens
malfunction.
Light Block Sheet
LNS-W07
LNS-W04/LNS-W05/LNS-W06
TYPE F14A (610 315 7337)
Light Block Sheet Holder
TYPE F14B (610 315 7320)
Fig-8
Fig-9
w
Back
To unfold, reverse the light block sheet and
release the latch.
Back of Light
Block Sheet
q
Front Cover
Replace the front cover and secure it with the 5
screws.
7
Fig-10
-5-
|