Renesas Network Card PCA7447FP User Guide

PCA7447FP  
PROM Programming Adapter for M38C89EFFP  
User's Manual  
Rev.1.00  
September 1, 2003  
REJ10J0253-0100Z  
 
Contents  
Chapter 1. Precautions for Safety ...........................................................................................4  
1.1 Safety Symbols and Meanings ..............................................................................4  
Chapter 2. Introduction...........................................................................................................6  
2.1 Things to Check When Unpacking .......................................................................6  
Chapter 3. Specifications ........................................................................................................7  
Chapter 4. How to Write the Program ....................................................................................8  
4.1 Programming Procedure........................................................................................8  
4.2 Attaching Adapter to PROM Programmer............................................................9  
4.3 Inserting MCU into Adapter ...............................................................................10  
4.4 Precautions When Opening and Closing the IC Socket ......................................11  
4.5 Caution to Be Taken for This Product ................................................................11  
4.6 Setting a Programming Area ...............................................................................11  
Chapter 5. Recommended PROM Programmers..................................................................12  
Chapter 6. Memory Maps .....................................................................................................13  
Chapter 7. Troubleshooting ..................................................................................................14  
7.1 Errors That Occur When Writing to PROM .......................................................14  
7.1.1 When Newly Purchased ........................................................................14  
7.1.2 Previously Written Normally ................................................................14  
7.2 MCUs Do Not Function Normally......................................................................15  
7.3 Other Precautions ................................................................................................15  
7.3.1 About the Recommended PROM Programmers...................................15  
7.3.2 About Reading Out of Device Identification Code ..............................15  
7.4 How to Request for Support................................................................................15  
To use the product properly  
Precautions for Safety:  
• Both in this User's Manual and on the product itself, several icons are used to insure  
proper handling of this product and also to prevent injuries to you or other persons,  
or damage to your properties.  
• The icons' graphic images and meanings are given in "Chapter 1. Precautions for  
Safety" (page 4). Be sure to read this chapter before using the product.  
( 3 / 18 )  
 
Chapter 1. Precautions for Safety  
In both the user's manual and on the product itself, several icons are used to insure proper handling  
of this product and also to prevent injuries to you or other persons, or damage to your properties.  
This chapter describes the precautions which should be taken in order to use this product safely and  
properly. Be sure to read this chapter before using this product.  
1.1 Safety Symbols and Meanings  
If the requirements shown in the "WARNING"  
sentences are ignored, the equipment may  
cause serious personal injury or death.  
WARNING  
If the requirements shown in the "CAUTION"  
sentences are ignored, the equipment may  
malfunction.  
CAUTION  
It means important information on using this  
product.  
IMPORTANT  
In addition to the three above, the following are also used as appropriate.  
means WARNING or CAUTION.  
Example:  
CAUTION AGAINST AN ELECTRIC SHOCK  
means PROHIBITION.  
Example:  
DISASSEMBLY PROHIBITED  
means A FORCIBLE ACTION.  
Example:  
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.  
The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".  
( 4 / 18 )  
 
WARNING  
Warnings for Use Environment:  
• This equipment is to be used in an environment with a maximum ambient temperature of 35˚C. Care  
should be taken that this temperature is not exceeded.  
• Select the proper programming mode of the PROM programmer.  
CAUTION  
Cautions to Be Taken for This Product:  
• Do not disassemble or modify this product. Disassembling or modifying this product can cause  
damage. Disassembling and modifying the product will void your warranty.  
• Use caution when handling this product. Be careful not to apply a mechanical shock such as falling.  
• Do not directly touch the connector pins of this product.  
• Be careful with the static electricity when handling this product and the MCU.  
Caution for Keeping This Product:  
• When not using this product for a long time:  
(1) Attach the connector pins of this product to the conductive sponge.  
(2) Put it into a conductive polyvinyl, and keep it in the package case shipped from the factory.  
(3) Store it in the place where humidity and temperature are low and direct sunshine does not  
strike.  
IMPORTANT  
When Using The Product:  
• Attach this product to the IC socket on the PROM programmer properly.  
• Insert the MCU to the IC socket of this product properly.  
• When inserting and pulling out the MCU, be sure to keep the IC socket side above and horizontal.  
• Be sure to set the programming area according to your PROM programmer.  
• Do not use the PROM programmer's device identification code readout function.  
( 5 / 18 )  
 
Chapter 2. Introduction  
The PCA7447FP is a PROM programming adapter for M38C89EFFP (8-bit MCU). The PCA7447FP  
is used to write programs into the internal EPROM of MCU with commercially available PROM  
programmer.  
This manual mainly explains specifications of PCA7447FP and how to operate it.  
Figure 2.1 shows the external view of the product and its constituent parts.  
Figure 2.1 External view of adapter and constituent parts (IC socket: QFP)  
2.1 Things to Check When Unpacking  
This product consists of the parts listed in Table 2.1. When unpacking, check to see that it contains  
all of the components.  
Table 2.1 Package components  
Main unit  
PCA7447FP  
Interface unit  
Connector  
PCA7402B  
PCA7402E (32-pin)  
This manual  
User's manual  
* If any part is missing or there is any doubt about your product package, contact your local  
distributor.  
( 6 / 18 )  
 
Chapter 3. Specifications  
Table 3.1 lists specifications of the programming adapters.  
Table 3.1 Specifications  
1MHz  
Operating clock frequency  
Power supply  
PCA7447FP  
(Supplied by the ceramic oscillator mounted on the adapter)  
Supplied from Vcc of the PROM programmer  
Board to insert a programmable MCU  
(IC socket mounted on it)  
(Main unit)  
Interface board  
Board  
configuration  
(Connected by two rows of standard-pitch 18-pin connectors  
and two rows of standard-pitch 16-pin connectors to the  
upper and lower boards)  
PCA7402B  
(Interface unit)  
PCA7402E  
(Connector)  
Board to connect to the PROM programmer  
(Standard-pitch 32-pin pin-header mounted)  
( 7 / 18 )  
 
Chapter 4. How to Write the Program  
This chapter describes procedures you need to follow when writing the program.  
For details on how to operate the PROM programmer, refer to the user's manual of the PROM  
programmer.  
4.1 Programming Procedure  
Follow steps (1) to (7) below to write the program.  
(1) Read the program into the PROM programmer.  
(2) Attach the adapter to the IC socket of the PROM programmer.  
See "4.2 Attaching Adapter to PROM Programmer" (page 9).  
(3) Insert the MCU into the adapter.  
See "4.3 Inserting MCU into Adapter" (page 10).  
(4) Set the programming area with the PROM programmer.*1  
See "4.6 Setting a Programming Area" (page 11).  
(5) Check to erase the programming area.*2  
Using the PROM programmer's erase check function, check whether data can be written into the  
MCU's programming area.  
(6) Write the program into the programming area of the MCU using the PROM programmer.*2  
(7) Verify the programming area of the MCU using the PROM programmer to check whether the  
program has been written into the MCU correctly.*2  
*1 Be sure to set the programming area. Otherwise the mode's shift to the programming mode may  
not be performed successfully. The erase check function and others may not also be performed  
completely.  
*2 Some PROM programmers perform the steps (5) to (7) automatically.  
( 8 / 18 )  
 
4.2 Attaching Adapter to PROM Programmer  
As shown in Figure 4.1, attach the No. 1 pin of the PCA7402E connector (standard-pitch 32-pin pin-  
header mounted) to the No. 1 pin of the IC socket of the PROM programmer.  
Be careful when attaching to the PROM programmer because incorrect insertion  
can cause fatal damage to the MCU.  
Figure 4.1 Attaching adapter to PROM programmer  
( 9 / 18 )  
 
4.3 Inserting MCU into Adapter  
As shown in Figure 4.2, insert the MCU into the IC socket with the No. 1 pin of the MCU matched  
to the No. 1 pin of the IC socket on the PCA7447FP.  
Be careful when attaching to the PROM programmer because incorrect insertion  
can cause fatal damage to the MCU.  
Top view  
Figure 4.2 Inserting an MCU (IC socket: QFP)  
( 10 / 18 )  
 
4.4 Precautions When Opening and Closing the IC Socket  
When opening and closing the IC socket, keep the IC socket side above and horizontal. Otherwise  
the inside of the IC socket may become damaged and cause an electrical insulation failure. Figure 4.3  
shows the state of opening and closing the IC socket to insert the MCU.  
Side view  
Figure 4.3 Opening and closing the IC socket and inserting MCU  
4.5 Caution to Be Taken for This Product  
Do not touch the connector in the IC socket and the pins on the PROM programmer connector because  
dirt may cause an electrical insulation failure.  
When not using this product, attach the connector pins of this product to the conductive sponge as  
it was shipped from the factory.  
4.6 Setting a Programming Area  
When writing and erasing programs, be sure to set the programming area. And also, specify its device  
of the PROM programmer.  
Table 4.1 Programming area  
PROM programmer  
Internal memory  
MCU  
ROM size  
60KB  
area of MCU  
Device  
Programming area  
0108016 - 0FFFD16  
M38C89EFFP  
M5M27C101  
108016 - FFFD16  
( 11 / 18 )  
 
Chapter 5. Recommended PROM Programmers  
The PROM programmers listed in Table 5.1 are recommended for this product. Using the actual  
products, we have verified that these PROM programmers can be used to write programs without  
problem. Nonconformity occurring by using any other PROM programmers can not be supported.  
For the latest type of PROM programmers, contact the manufacturer to confirm whether it can be used  
for your product.  
Table 5.1 Recommended PROM programmers  
Programming voltage  
Manufacturer  
Type name  
Device  
(Vpp)  
R4945  
Advantest Corporation  
M5M27C101 mode  
12.5V  
R4945A  
( 12 / 18 )  
 
Chapter 6. Memory Maps  
Figure 6.1 shows memory maps of the MCU and the PROM programmer.  
000016  
0000016  
Unused area  
100016  
Reserved ROM area  
107F16  
108016  
0107F16  
0108016  
Internal  
memory area  
(60K bytes)  
Programming area  
Unused area  
FFFD16  
FFFE16  
0FFFD16  
0FFFE16  
Reserved ROM area  
FFFF16  
0FFFF16  
1000016  
Unused area  
1FFFF16  
MCU  
PROM programmer  
(M5M27C101 mode)  
Figure 6.1 Memory maps  
( 13 / 18 )  
 
Chapter 7. Troubleshooting  
The table below summarizes errors to be checked carefully before you determine them to be a fault.  
7.1 Errors That Occur When Writing to PROM  
7.1.1 When Newly Purchased  
Remedy  
Cause  
See page  
9
Is the adapter attached to the correct position of the PROM  
programmer?  
Programming adapter  
Is the MCU attached to the correct position?  
Is the area specification set correctly?  
Is the correct device selected?  
10  
11  
12  
PROM programmer  
Contact failure  
The IC socket of the PROM programmer may be stained. The  
socket needs replacing.  
-
7.1.2 Previously Written Normally  
Remedy  
Cause  
See page  
9
Is the adapter attached to the correct position of the PROM  
programmer?  
Programming adapter  
PROM programmer  
Is the MCU attached to the correct position?  
Is the area specification set correctly?  
Is the correct device selected?  
10  
11  
12  
The IC socket of the PROM programmer may be stained. The  
socket needs replacing.  
-
-
Contact failure  
The PROM programmer connector at which the PROM  
programmer is contacted may be stained. Clean it with alcohol,  
etc.  
( 14 / 18 )  
 
7.2 MCUs Do Not Function Normally  
The program operates normally on the emulator, but when the MCU that has normally been written  
is attached the same program does not function normally.  
(1) Is the offset address specified correctly when copying data into the PROM programmer?  
(2) In the emulator, NOPs are often inserted in the area where the program has not been read, therefore  
the program happens to appear functioning normally even though it may have gone wild. Check  
your program again.  
(3) The emulator and the actual MCU may differ in characteristics. Consult the user's manual of the  
emulation pod to check for differences in characteristics again.  
7.3 Other Precautions  
7.3.1 About the Recommended PROM Programmers  
Not all PROM programmers available on the market can be checked to see if they function properly.  
There are several PROM programmers that we have verified to function properly. These products are  
listed as recommended PROM programmers in this user's manual. Other PROM programmers may  
also be used providing that you verified them to function properly.  
Note: No matter which type of PROM programmer you use, it is necessary to verify completion of  
programming by executing screening, etc. that are stipulated for each MCU used.  
7.3.2 About Reading Out of Device Identification Code *1  
Please do not use the PROM programmer's device identification code readout function.  
Using this function may break down the MCU. The device identification code is included in EPROM  
to indicate the manufacturer code and device code; it is not included in the MCU.  
1
*
Depending on PROM programmer manufacturers, this may be referred to by another name (e.g.  
ID code).  
7.4 How to Request for Support  
After checking this manual, fill in the following information and email to your local distributor.  
For prompt response, please specify the following information:  
(1) Contact address  
• Company name  
• Department  
• Responsible person  
• Phone number  
• Fax number  
• E-mail address  
(2) Product information  
• Name of the programming adapter  
• Serial number  
• Date of purchase  
• Target MCU  
• Symptoms (Fails blank check/Cannot write a program/Fails verification etc.)  
• Detailed symptoms  
• How often does the problem occur? (2 out of 10 etc.)  
• When did the problem start to occur? (Since purchase/Used to work correctly)  
• Type name of the PROM programmer (Advantest R4945A etc.)  
• Specified device when writing to PROM (M27C101 etc.)  
• Specified programming area when writing to PROM  
• Switch settings of the adapter when writing to PROM  
( 15 / 18 )  
 
MEMO  
( 16 / 18 )  
 
PCA7447FP User's Manual  
Rev.1.00  
September 1, 2003  
REJ10J0253-0100Z  
COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION  
AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED  
 
 

Reebok Watch W 112 User Guide
Renesas Network Card HS7710KCM02HE User Guide
Ricoh Film Camera RICOH WG 30W User Guide
RightWay GPS Receiver RW 430 User Guide
Roadmaster Speaker System RS3000T User Guide
Roland Electronic Keyboard DP 900 User Guide
Samsung Answering Machine SVM 400E User Guide
Sanyo Air Conditioner C4232 User Guide
Sanyo DVD VCR Combo HV DX1E User Guide
Sanyo Freezer SF L6111 User Guide