Renesas Network Card HS1664ECH61H User Guide

REJ10J1395-0100  
H8SX/1663 Group E6000H FP-144L  
User System Interface Board  
HS1664ECH61H User’s Manual  
Renesas Microcomputer Development Environment System  
H8SX Family / H8SX/1600 Series  
HS1664ECH61HE  
Rev.1.00  
 
Revision Date: Jun. 28, 2006  
Keep safety first in your circuit designs!  
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and  
more reliable, but there is always the possibility that trouble may occur with them. Trouble with  
semiconductors may lead to personal injury, fire or property damage.  
Remember to give due consideration to safety when making your circuit designs, with appropriate  
measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or  
(iii) prevention against any malfunction or mishap.  
Notes regarding these materials  
1. These materials are intended as a reference to assist our customers in the selection of the Renesas  
Technology Corp. product best suited to the customer's application; they do not convey any license  
under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or  
a third party.  
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-  
party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or  
circuit application examples contained in these materials.  
3. All information contained in these materials, including product data, diagrams, charts, programs and  
algorithms represents information on products at the time of publication of these materials, and are  
subject to change by Renesas Technology Corp. without notice due to product improvements or  
other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or  
an authorized Renesas Technology Corp. product distributor for the latest product information  
before purchasing a product listed herein.  
The information described here may contain technical inaccuracies or typographical errors.  
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising  
from these inaccuracies or errors.  
Please also pay attention to information published by Renesas Technology Corp. by various means,  
including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com).  
4. When using any or all of the information contained in these materials, including product data,  
diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total  
system before making a final decision on the applicability of the information and products. Renesas  
Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the  
information contained herein.  
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or  
system that is used under circumstances in which human life is potentially at stake. Please contact  
Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when  
considering the use of a product contained herein for any specific purposes, such as apparatus or  
systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.  
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in  
whole or in part these materials.  
7. If these products or technologies are subject to the Japanese export control restrictions, they must  
be exported under a license from the Japanese government and cannot be imported into a country  
other than the approved destination.  
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the  
country of destination is prohibited.  
8. Please contact Renesas Technology Corp. for further details on these materials or the products  
contained therein.  
 
 
IMPORTANT INFORMATION  
READ FIRST  
• READ this user's manual before using this user system interface board.  
• KEEP the user's manual handy for future reference.  
Do not attempt to use the user system interface board until you fully understand its  
mechanism.  
User System Interface Board:  
Throughout this document, the term "user system interface board" shall be defined as the  
following product produced only by Renesas Technology Corp. excluding all subsidiary products.  
User system interface board (HS1664ECH61H)  
The user system or a host computer is not included in this definition.  
Purpose of the User System Interface Board:  
This user system interface board is for connecting the evaluation chip board and user system.  
This user system interface board must only be used for the above purpose.  
Improvement Policy:  
Renesas Technology Corp. (including its subsidiaries, hereafter collectively referred to as  
Renesas) pursues a policy of continuing improvement in design, performance, functions, and  
safety of the user system interface board. Renesas reserves the right to change, wholly or  
partially, the specifications, design, user's manual, and other documentation at any time without  
notice.  
Target User of the User System Interface Board:  
This user system interface board should only be used by those who have carefully read and  
thoroughly understood the information and restrictions contained in the user's manual. Do not  
attempt to use the user system interface board until you fully understand its mechanism.  
It is highly recommended that first-time users be instructed by users that are well versed in the  
operation of the user system interface board.  
I
 
LIMITED WARRANTY  
Renesas warrants its user system interface boards to be manufactured  
in accordance with published specifications and free from defects in  
material and/or workmanship. Renesas will repair or replace any  
user system interface boards determined to be defective in material  
and/or workmanship. User system interface boards are wearing parts  
which Renesas will not repair or replace if damaged and/or worn  
through use. The foregoing shall constitute the sole remedy for any  
breach of Renesas’ warranty. This warranty extends only to you, the  
original Purchaser. It is not transferable to anyone who subsequently  
purchases the user system interface board from you. Renesas is not  
liable for any claim made by a third party or made by you for a third  
party.  
DISCLAIMER  
RENESAS MAKES NO WARRANTIES, EITHER EXPRESS OR  
IMPLIED, ORAL OR WRITTEN, EXCEPT AS PROVIDED  
HEREIN, INCLUDING WITHOUT LIMITATION THEREOF,  
WARRANTIES AS TO MARKETABILITY, MERCHANTABILITY,  
FITNESS FOR ANY PARTICULAR PURPOSE OR USE, OR  
AGAINST INFRINGEMENT OF ANY PATENT. IN NO EVENT  
SHALL RENESAS BE LIABLE FOR ANY DIRECT, INCIDENTAL  
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR  
LOSSES OR EXPENSES RESULTING FROM ANY DEFECTIVE  
USER SYSTEM INTERFACE BOARD, THE USE OF ANY USER  
SYSTEM INTERFACE BOARD, OR ITS DOCUMENTATION,  
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.  
EXCEPT AS EXPRESSLY STATED OTHERWISE IN THIS  
WARRANTY, THIS USER SYSTEM INTERFACE BOARD IS SOLD  
"AS IS ", AND YOU MUST ASSUME ALL RISK FOR THE USE  
AND RESULTS OBTAINED FROM THE USER SYSTEM  
INTERFACE BOARD.  
II  
 
State Law:  
Some states do not allow the exclusion or limitation of implied warranties or liability for  
incidental or consequential damages, so the above limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights, and you may have other rights which may vary from  
state to state.  
The Warranty is Void in the Following Cases:  
Renesas shall have no liability or legal responsibility for any problems caused by misuse,  
abuse, misapplication, neglect, improper handling, installation, repair or modifications of the user  
system interface board without Renesas’ prior written consent or any problems caused by the user  
system.  
All Rights Reserved:  
This user's manual and user system interface board are copyrighted and all rights are reserved  
by Renesas. No part of this user's manual, all or part, may be reproduced or duplicated in any  
form, in hard-copy or machine-readable form, by any means available without Renesas’ prior  
written consent.  
Other Important Things to Keep in Mind:  
1. Circuitry and other examples described herein are meant merely to indicate the characteristics  
and performance of Renesas’ semiconductor products. Renesas assumes no responsibility for  
any intellectual property claims or other problems that may result from applications based on  
the examples described herein.  
2. No license is granted by implication or otherwise under any patents or other rights of any third  
party or Renesas.  
Figures:  
Some figures in this user's manual may show items different from your actual system.  
Limited Anticipation of Danger:  
Renesas cannot anticipate every possible circumstance that might involve a potential hazard.  
The warnings in this user's manual and on the user system interface board are therefore not all  
inclusive. Therefore, you must use the user system interface board safely at your own risk.  
III  
 
SAFETY PAGE  
READ FIRST  
• READ this user's manual before using this user system interface board.  
• KEEP the user's manual handy for future reference.  
Do not attempt to use the user system interface board until you fully understand its  
mechanism.  
DEFINITION OF SIGNAL WORDS  
This is the safety alert symbol. It is used to alert you to potential personal  
injury hazards. Obey all safety messages that follow this symbol to avoid  
possible injury or death.  
DANGER  
DANGER indicates an imminently hazardous situation which, if not  
avoided, will result in death or serious injury.  
WARNING  
WARNING indicates a potentially hazardous situation which, if not  
avoided, could result in death or serious injury.  
CAUTION  
CAUTION indicates a potentially hazardous situation which, if not  
avoided, may result in minor or moderate injury.  
CAUTION  
CAUTION used without the safety alert symbol indicates a  
potentially hazardous situation which, if not avoided, may result  
in property damage.  
NOTE emphasizes essential information.  
IV  
 
WARNING  
Observe the precautions listed below. Failure to do so  
will result in a FIRE HAZARD and will damage the user  
system and the emulator product or will result in  
PERSONAL INJURY. The USER PROGRAM will be  
LOST.  
1. Do not repair or remodel the emulator product by  
yourself for electric shock prevention and quality  
assurance.  
2. Always switch OFF the E6000H emulator and user system  
before connecting or disconnecting any CABLES or  
PARTS.  
3. Always before connecting any BOARDS, make sure that  
pin 1 on both sides are correctly aligned.  
V
 
Preface  
The HS1664ECH61H is a user system interface board that connects a user system for the  
H8SX/1663, H8SX/1664 FP-144L package to the H8SX/1650 E6000H emulator  
(HS1650EPH60H). Emulation of the H8SX/1663 group is only possible when this user system  
interface board is connected to the HS1650EPH60H.  
i
 
Contents  
Section 1 Configuration.....................................................................................1  
Section 2 Connection Procedures......................................................................3  
2.1 Connecting the User System Interface Board to the User System.................................... 3  
2.1.1 Installing the IC Socket........................................................................................ 4  
2.1.2 Soldering the IC Socket....................................................................................... 5  
2.1.3 Inserting the IC Socket Connector....................................................................... 5  
2.1.4 Fastening the IC Socket Connector...................................................................... 6  
2.2 Exchanging the Spacers of the Evaluation Chip Board .................................................... 8  
2.3 Connecting the User System Interface Board to the Evaluation Chip Board ................... 9  
2.4 Recommended Dimensions for the User System Mounting Pad (Footprint).................... 11  
2.5 Dimensions of the Evaluation Chip Board and the User System Interface Board............ 12  
2.6 Resulting Dimensions after Connecting the User System Interface Board....................... 13  
2.7 Using the Emulator without Connecting User System ..................................................... 14  
Section 3 User System Interface Circuits..........................................................16  
Section 4 Verifying Operation...........................................................................19  
Section 5 Points for Caution..............................................................................21  
Section 6 Restrictions........................................................................................23  
ii  
 
Section 1 Configuration  
Figure 1 and table 1 show the configuration and components of the user system interface board for  
the FP-144L package. Please make sure you have all of these components after you have  
unpacked the box.  
Evaluation chip board  
Screws (M2 × 6 mm)  
Spacer  
Screws (M2 × 10 mm)  
(for fastening the board)  
Socket cover  
User system  
interface board  
IC socket  
User system  
Figure 1 User System Interface Board for the H8SX/1663, H8SX/1664 FP-144L Package  
1
 
CAUTION  
Use an NQPACK144SD socket (manufactured by  
Tokyo Eletech Corporation) as the FP-144L-packaged  
IC socket on the user system.  
Table 1  
HS1664ECH61H Components  
No. Component  
Quantity Remarks  
1
2
User system interface  
board  
1
1
IC socket  
For the FP-144L package (to be mounted on the user  
system)  
3
4
5
6
7
8
9
Socket cover  
1
4
4
For installing an FP-144L-packaged MCU  
For fastening the board  
Screw (M2 x 10 mm)  
Screw (M2 x 6 mm)  
For installing an FP-144L-packaged MCU  
Spacers (2.6MP x 25 mm) 2  
Spacers (2.6MQ x 13 mm) 4  
Screwdriver  
1
3
1
For tightening screws  
Guide pins (φ1 mm)  
For determining the IC socket location  
User’s manual for HS1664ECH61H (this manual)  
10 Documentation  
2
 
Section 2 Connection Procedures  
Connecting the User System Interface Board to the User System  
WARNING  
2.1  
Always switch OFF the user system and the emulator  
product before the USER SYSTEM INTERFACE BOARD  
is connected or removed. Before connecting the two, make  
sure that pin 1 on both sides are correctly aligned. Failure to  
do so will result in a FIRE HAZARD and will damage the  
user system and the emulator product or will result in  
PERSONAL INJURY. The USER PROGRAM will be LOST.  
CAUTION  
1. Do not connect a 5-V signal to any pin, including the  
USB pins. Incorrect usage will cause damage to the  
emulator product, user system interface board, and  
user system.  
2. To connect the emulator to the user system, ensure that  
the SW1 jumper pin is inserted to [USER-ON].  
Failure to do so will damage the emulator product, user  
system interface board, and user system.  
3
 
To connect the board to the user system, follow the instructions below.  
2.1.1 Installing the IC Socket  
After checking the location of pin 1 on the IC socket fasten it to the user system before soldering.  
CAUTION  
After confirming the location of pin 1 on the IC socket,  
apply epoxy resin adhesive to the end of the four projections  
at the bottom of the IC socket, and fasten it to the user  
system.  
Use the guide pins provided with the product to determine where to install the IC socket, as shown  
in figure 2.  
Guide pins  
4 projections to apply  
epoxy resin adhesive to  
IC socket  
(NQPACK144SD manufactured  
Pin 1  
by Tokyo Eletech Corporation)  
Bottom view of IC soket  
User system  
Figure 2 Correctly Placing the IC Socket  
4
 
2.1.2  
Soldering the IC Socket  
After fastening, solder the IC socket for an FP-144L package to the user system.  
CAUTION  
Be sure to completely solder the leads so that the solder  
gently covers the leads and forms solder fillets. (Use  
slightly more solder than with the MCU.)  
2.1.3  
Inserting the IC Socket Connector  
CAUTION  
Check the location of pin 1 before inserting.  
After checking the location of pin 1 on the user system interface board and pin 1 on the IC socket  
connector, align the guide pins on the IC socket connector with the guide holes on the user system  
interface board, and insert the IC socket connector into the IC socket (figure 3).  
5
 
2.1.4  
Fastening the IC Socket Connector  
CAUTION  
1. Use the screwdriver provided for tightening screws.  
2. The tightening torque must be 0.054 N•m or less.  
If the applied torque cannot be accurately measured,  
stop tightening when the force required to turn the screw  
becomes significantly greater than that needed when first  
tightening. If a screw is tightened too much, the screw  
head may break or an IC socket contact error may be  
caused by a crack in the IC socket solder.  
3. If the emulator does not operate correctly, cracks might  
have occurred in the solder. Check conduction with  
a tester and re-solder the IC socket if necessary.  
Fasten the user system interface board to the IC socket for an FP-144L package on the user system  
with the four screws (M2 x 10 mm) provided. Each screw should be tightened a little at a time,  
alternating between screws on opposing corners. Take special care, such as manually securing the  
IC socket soldered area, to prevent the soldered IC socket from being damaged by overtightening  
the screws or twisting the components.  
6
 
Screws (M2 × 10 mm)  
(for fastening the board)  
User system interface board  
Pin 1  
IC socket  
(NQPACK144SD  
manufactured by  
Tokyo Eletech Corporation)  
User system  
Figure 3 Connecting the User System Interface Board to the User System  
7
 
2.2  
Exchanging the Spacers of the Evaluation Chip Board  
After connecting the user system interface board to the user system, be careful not to apply load to  
the user system.  
Exchange the spacers (2.6MP × 10 mm) of the evaluation chip board with the spacers (2.6MP ×  
25 mm) provided with the user system interface board and adjust the height.  
Evaluation chip board  
Spacer  
(2.6MP × 25 mm)  
Figure 4 Exchanging the Spacers  
8
 
2.3  
Connecting the User System Interface Board to the Evaluation Chip  
Board  
WARNING  
Observe the precautions listed below. Failure to do so  
will result in a FIRE HAZARD and will damage the user  
system and the emulator product or will result in  
PERSONAL INJURY. The USER PROGRAM will be  
LOST.  
1. Always switch OFF the user system and the emulator  
product before the USER SYSTEM INTERFACE BOARD  
is connected or removed. Before connecting the two,  
make sure that the pin 1 positions on both sides are  
correctly aligned.  
2. The user system interface board must be used with the  
emulator for which it was designed.  
1. Make sure the user system and emulator are turned off.  
2. Align the connectors on the user system interface board with those on the evaluation chip  
board by matching the numbers on the connectors (figure 5).  
3. Adjust the height of the spacers of the evaluation chip board to accommodate the user system.  
9
 
Evaluation chip board  
Connector No.  
Evaluation  
Chip Board  
Connector No.  
Board  
Connector No.  
UCN1  
UCN2  
UCN1  
UCN2  
User system interface board  
Figure 5 Connecting the User System Interface Board to the Evaluation Chip Board  
10  
 
2.4  
Recommended Dimensions for the User System Mounting Pad  
(Footprint)  
Figure 6 shows the recommended dimensions for the mounting pad (footprint) for the user system  
with the IC socket for an FP-144L package (NQPACK144SD: manufactured by Tokyo Eletech  
Corporation). Note that the dimensions in figure 6 are somewhat different from those of the  
mounting pad for the system with the actual MCU.  
23.00 0.15  
11.50  
2.00 0.10  
0.50  
0.25 (max.)  
Unit: mm  
Tolerance:  
0.10 mm  
Figure 6 Recommended Dimensions for the Mounting Pad  
11  
 
2.5  
Dimensions of the Evaluation Chip Board and the User System  
Interface Board  
The dimensions of the evaluation chip board and the user system interface board are shown in  
figure 7.  
140.0  
Evaluation chip board  
118.5  
102.5  
16.0  
78.5  
User system interface board  
Unit: mm  
Tolerance: 0.5 mm  
Figure 7 Dimensions of the Evaluation Chip Board and the User System Interface Board  
12  
 
2.6  
Resulting Dimensions after Connecting the User System Interface  
Board  
The dimensions of the assembly after the user system interface board has been connected to the  
user system are shown in figure 8.  
Evaluation chip board  
56.5  
IC socket  
(NQPACK144SD  
manufactured by  
Tokyo Eletech Corporation)  
Spacer (φ5.8)  
User system  
56.5  
Unit: mm  
Tolerance: 1.0 mm  
Figure 8 Dimensions of the Assembly after Connection of the User System Interface Board  
13  
 
2.7  
Using the Emulator without Connecting User System  
WARNING  
Always switch OFF the user system and the emulator  
product before the USER SYSTEM INTERFACE BOARD  
is connected or removed. Before connecting the two, make  
sure that pin 1 on both sides are correctly aligned. Failure to  
do so will result in a FIRE HAZARD and will damage the  
user system and the emulator product or will result in  
PERSONAL INJURY. The USER PROGRAM will be LOST.  
CAUTION  
When this emulator is used without connecting to the  
user system, ensure that the SW1 jumper pin is inserted to  
[USER-OFF]. Failure to do so will damage the emulator  
product, user system interface cable, and user system.  
Attach the provided spacers (2.6MQ x 13 mm) to four positions on the user system interface board  
not to apply loads to the connector (CN1) on the board (figure 10).  
14  
 
USER ON  
SW1  
P1  
USER OFF  
Figure 9 SW1 Jumper Socket  
Spacer  
(2.6MQ x 13 mm)  
Figure 10 Attaching Spacers  
15  
 
Section 3 User System Interface Circuits  
The following user interface circuits are required for the emulator when the user system interface  
board is in use.  
User system  
Vcc  
Sub-MCU  
Monitoring  
circuit  
EPM7128  
47 kΩ  
MD3  
Vcc  
MD control  
circuit  
Monitoring  
circuit  
LPT16244  
47 kΩ  
MD_CLK  
MD_CLK  
PM0-PM4  
VBUS  
PM0-PM4  
VBUS  
EPM7128  
1 kΩ  
DrVcc  
USD-  
DrVcc  
Power-supply  
circuit  
USD-  
USD+  
DrVss  
USD+  
DrVss  
Figure 11 User System Interface Circuit (1)  
Note: The power-supply circuit shown above is turned on/off by the setting of the SW1 jumper  
pin on HS1664ECH61H. Ensure that the jumper pin is inserted to [USER-ON] on  
HS1664ECH61H when connecting the emulator (with HS1664ECH61H attached) to the  
user system or supplying power to DrVCC. Otherwise the emulator product, user system  
interface board, and user system will be damaged.  
16  
 
MCU  
User system  
SN74CB3Q3306A  
P23  
P27  
P23  
P27  
SN74CB3Q3306A  
Figure 12 User System Interface Circuit (2)  
MCU  
User system  
P14  
SN74CB3Q3306A  
P14  
Sub-MCU  
SN74CB3Q3306A  
TXD  
Figure 13 User System Interface Circuit (3)  
17  
 
MCU  
User system  
_RES  
Vcc  
EPM7128  
UHC14  
VHC244  
47 kΩ  
_RES  
EPM7128  
Figure 14 User System Interface Circuit (4)  
18  
 
Section 4 Verifying Operation  
1. Turn on the emulator according to the procedures described in the H8SX/1650 E6000H  
Emulator User's Manual (HS1650EPH60HE).  
2. Verify the user system interface cable connections by checking the pin states with the  
EXMONITOR_DISPLAY command (emulator command) and checking the bus states with  
the MEMORY_FILL command (emulator command). If an error is detected, recheck the  
soldered IC socket and the location of pin 1.  
3. The emulator connected to this user system interface board supports three kinds of clock  
sources as the MCU clock. For details, refer to the H8SX/1650 E6000H Emulator User's  
Manual (HS1650EPH60HE).  
To use the emulator internal clock  
Select the clock in the emulator by the CLOCK command (emulator command).  
To use the external clock on the user system  
Supply the external clock from the user system to the emulator by inputting the signal to  
the EXTAL pin (pin 98) on the user system interface board or connecting a crystal  
oscillator to the XTAL (pin 97) and EXTAL pins. For details, refer to the H8SX/1650  
Hardware Manual.  
Figure 15 shows the clock oscillator on the user system interface board.  
HCU04  
1 MΩ  
HCU04 HCU04  
HCU04  
HCU04  
0 Ω  
To E6000H  
emulator  
HCU04  
270 Ω  
EXTAL XTAL  
System clock  
Figure 15 Clock Oscillator  
19  
 
To use the crystal oscillator mounted on the evaluation chip board  
Install the crystal oscillator into the crystal oscillator terminals on the evaluation chip  
board.  
Enlarged  
view  
Crystal  
oscillator  
X1  
X2  
Crystal oscillator terminals  
Evaluation chip  
board  
Figure 16 Installing the Clock Oscillator  
20  
 
Section 5 Points for Caution  
1. Before connecting any parts or cables, make sure that the pins at the pin 1 position on both  
sides are correctly aligned.  
2. Do not apply excessive force to the user system interface board while it is connected to the  
user system.  
3. The dimensions of the recommended mounting pad for the IC socket for this user system  
interface board are different from those of the pad for the MCU.  
4. This user system interface board is specifically designed for the HS1650EPH60H emulator.  
Do not use this board with any other emulator.  
5. When power is not being supplied to the Vcc pin on the user system interface board, the  
emulator displays ** VCC DOWN. In this situation, the emulator will not operate correctly.  
6. The P1 short connector is used for testing. Do not remove the inserted jumper pin.  
Do not remove the  
jumper pin.  
1
3
P1  
USER ON  
SW1  
USER OFF  
Figure 17 Jumper Socket  
7. Do not connect this user system interface board to the user system for the H8SX/1650 group.  
21  
 
8. When you use the emulator without connecting it to the user system, ensure that the SW1  
jumper pin is inserted to [USER-OFF]. While no pin or SW1 jumper pin is inserted to  
[USER-OFF], the emulator supplies 3.3-V power to DrVCC, which is the power supply  
exclusively used for USB.  
9. To connect the emulator to the user system, ensure that the SW1 jumper pin is inserted to  
[USER-ON]. While SW1 jumper pin is inserted to [USER-ON], the emulator does not supply  
power to DrVCC, which is the power supply exclusively used for USB. Thus the power must  
be supplied from the user system instead.  
10. Do not connect a 5-V signal to any pin, including the USB pins. Incorrect usage will cause  
damage to the emulator product, user system interface board, and user system.  
22  
 
Section 6 Restrictions  
There are the following restrictions on emulation of the H8SX/1663 group when the user system  
interface board is connected to the emulator.  
1. The USB clock frequency is fixed to 48 MHz regardless of the EXTAL input.  
2. P14 cannot be used as a port if the serial output function has already been selected. The port  
pin state cannot be read from the port register.  
3. The user system interface board does not support subclock operation. Thus the following  
function and register cannot be used:  
- 32k timer  
- Subclock control register (SUBCKCR) of the clock pulse generator  
- Interrupt priority register D (IPRD2 to IPRD0)  
4. Exception processing of sleep instructions is not supported. Even if the SLPIE bit of the  
standby control register (SBYCR) is set to 1, the emulator enters the power-down mode and no  
exception processing of sleep instructions occurs.  
23  
 
H8SX/1663 Group E6000H FP-144L  
User System Interface Board  
HS1664ECH61H User's Manual  
Publication Date: Rev.1.00, June 28, 2006  
Published by:  
Sales Strategic Planning Div.  
Renesas Technology Corp.  
Customer Support Department  
Global Strategic Communication Div.  
Renesas Solutions Corp.  
Edited by:  
© 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.  
 
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan  
RENESAS SALES OFFICES  
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.  
Renesas Technology America, Inc.  
450 Holger Way, San Jose, CA 95134-1368, U.S.A  
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501  
Renesas Technology Europe Limited  
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.  
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900  
Renesas Technology (Shanghai) Co., Ltd.  
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120  
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898  
Renesas Technology Hong Kong Ltd.  
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong  
Tel: <852> 2265-6688, Fax: <852> 2730-6071  
Renesas Technology Taiwan Co., Ltd.  
10th Floor, No.99, Fushing North Road, Taipei, Taiwan  
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999  
Renesas Technology Singapore Pte. Ltd.  
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632  
Tel: <65> 6213-0200, Fax: <65> 6278-8001  
Renesas Technology Korea Co., Ltd.  
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea  
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145  
Renesas Technology Malaysia Sdn. Bhd  
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia  
Tel: <603> 7955-9390, Fax: <603> 7955-9510  
Colophon 6.0  
 
H8SX/1663 Group E6000H FP-144L  
User System Interface Board  
HS1664ECH61H User’s Manual  
 

Quasar Air Conditioner HQ 2081TH User Guide
Radio Shack Cordless Telephone ET 551 User Guide
Renesas Computer Hardware H8S 2168 User Guide
Renesas Network Card PCA7429G02 User Guide
Renesas Stereo System SH7709S User Guide
Ricoh Copier NC5006 User Guide
Roadmaster Car Speaker VSW120 User Guide
Samsung Camcorder WB700 User Guide
SATO All in One Printer GL 4xxe User Guide
Schneider Electric Weather Radio ION8800 User Guide