Renesas Computer Hardware M32186T2 PTC User Guide

M32186T2-PTC  
Converter for In-circuit Connection (for M32186FxxFP)  
User’s Manual  
Keep safety first in your circuit designs!  
1. Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products  
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to  
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with  
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention  
against any malfunction or mishap.  
Notes regarding these materials  
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited  
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to  
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.  
2. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of  
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application  
examples contained in these materials.  
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information  
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and  
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that  
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product  
distributor for the latest product information before purchasing a product listed herein. The information described here may contain  
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no  
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information  
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home  
page (http://www.renesas.com).  
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and  
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the  
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any  
damage, liability or other loss resulting from the information contained herein.  
5. Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under  
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions  
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any  
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.  
6. The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or  
reproduce in whole or in part these materials.  
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from  
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport  
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.  
8. Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the  
products contained therein.  
Precautions to be taken when using this product  
1. This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your  
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing  
integration test, evaluation, or some experiment else.  
2. In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.  
3. Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.  
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any  
circumstances.  
4. This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not  
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when  
used in Japan.  
If the requirements shown in the "CAUTION" sentences are ignored,  
the equipment may cause personal injury or damage to the products.  
CAUTION  
Renesas Tools Homepage http://www.renesas.com/tools  
Rev.2.00  
Oct. 16, 2006  
(1/6)  
REJ10J0971-0200  
 
5. Connection Procedure  
Connection to the M32100T-SDI-E or M32170T-SDI  
5.1 For M32100T-SDI-E or M32170T-SDI.  
(1) Mount the NQPACK144SD on the user system  
(2) Connect the YQPACK144SD on the NQPACK144SD.  
(3) Secure the four corners of the YQPACK144SD with the  
YQ-GUIDE’s.  
Interface cables of the pod probe  
(7)  
M3T- PTC- CNV  
(separately available)  
(6)  
(4) Mount the M32186T2-PTC on the YQPACK144SD.  
(5) Set the clock select switch.  
Clock select switch  
(5)  
(6) Mount the M3T-PTC-CNV on the M32186T2-PTC.  
M32186T2- PTC  
(4)  
(7) Connect the emulation pod probe to the M32186T2-PTC  
via the SDI MCU control interface cable and the SDI trace  
interface cable.  
YQ-GUIDE(x4)  
(3)  
YQPACK144SD  
NQPACK144SD  
(2)  
(1)  
144-pin 0.5mm pitch  
(144P6Q-A) foot pattern  
: No.1 pin  
Be sure to match the position of No. 1 pin of the foot pattern and each part.  
Figure 5.1 Connection Procedure (1)  
(3/6)  
 
Connection to M32100T2-SDI-E,  
M32100T3-SDI-E or M32100T5-SDI-E  
5.2 For M32100T2-SDI-E, M32100T3-SDI-E or  
M32100T5-SDI-E.  
(1) Mount the NQPACK144SD on the user system  
Emulator main unit or  
Emulator Probe  
(2) Connect the YQPACK144SD on the NQPACK144SD.  
(3) Secure the four corners of the YQPACK144SD with the  
YQ-GUIDE’s.  
(4) Mount the M32186T2-PTC on the YQPACK144SD.  
(5) Set the clock select switch.  
(6)  
Clock select switch  
(5)  
(6) Connect the emulator probe to the M32186T2-PTC.  
.
M32186T2-PTC  
(4)  
YQ-GUIDE(x4)  
(3)  
YQPACK144SD  
NQPACK144SD  
(2)  
(1)  
144-pin 0.5mm pitch  
(144P6Q--A) foot pattern  
: No.1 pin  
Be sure to match the position of No.1 pin of foot pattern and each part  
Figure 5.2 Connection Procedure (2)  
5.3 On-board Evaluation  
(1) Mount the NQPACK144SD on the user system  
(2) Mount the M32186FxxFP on the NQPACK144SD.  
(3) Mount the HQPACK144SD on the NQPACK144SD.  
HQPACK144SD  
(separately available)  
(3)  
M32186FxxFP  
(separately available)  
(2)  
NQPACK144SD  
(1)  
144-pin 0.5mm pitch  
(144P6Q-A) foot pattern  
: No. 1 pin  
Be sure to match the position of No. 1 pin of the foot pattern and each part.  
Figure 5.3 Connection Procedure (3)  
(4/6)  
 
6. Selecting a Clock  
Mount an oscillator to X2 as  
shown in the diagram printed on  
the boar.d  
With the M32186T2-PTC, it is possible to select a clock supply  
to the MCU by the clock select switch (SW1). Select a clock  
supply as shown below.  
However, when used with the M32186T2-PTC, the clock  
cannot be supplied from the user system.  
X2 socket  
Connected to XIN pin of MCU  
R1 0  
Connected to XOUT pin of MCU  
C1  
C2  
R 4  
R1 0  
R4  
C1  
C2  
(1) 8 MHz:  
:
:
:
:
1MΩ  
510Ω  
27pF  
27pF  
Supplies the clock (X1: 8 MHz) to the MCU from the  
oscillator on the M32186T2-PTC board  
(2) SOCKET:  
Supplies the clock to the MCU from the socket (X2) for  
mounting an oscillator on the M32186T2-PTC board. By  
mounting an oscillator to the X2 socket of the MCU, it is  
possible to change the operating frequency.  
Figure 6.1 shows the connecting the X2 socket and the  
MCU.  
Figure 6.1 Connection diagram of X2 socket  
7. External Dimensions and a Sample Foot Pattern of the M32186T2-PTC  
16  
85  
M32192T2 -PTC REV . A  
MADE IN JAPAN  
SOCKET  
SW1  
M Hz  
8
23  
19  
0.25  
for SL  
ø
3.2  
Hole for  
soldering NQ  
ø
3- 1.0  
7
0.5  
: No.1 pin  
Unit: mm  
Figure 7.1 External dimensions and a sample foot pattern of the M32186T2-PTC  
(5/6)  
 
8. Precautions  
CAUTION  
Cautions to Be Taken for Emulator:  
z For debugging, use this product in the combination with the SDI emulator, M32100-SDI-E, M32170T-SDI,  
M32100T2-SDI-E, M32100T3-SDI-E or M32100T5-SDI-E.  
z When using with the M32100T-SDI-E or M32170T-SDI, the following restrictions are applied according to the  
MCU operating frequency. The M32186T2-PTC is recommended to use with the M32100T3-SDI-E or  
M32100T5-SDI-E.  
- More than 66 MHz:  
Compared with the M32100T2-SDI-E, M32100T3-SDI-E, or M32100T5-SDI-E, more loss of trace information  
occurs.  
- 66 MHz or less:  
Same as the M32100T2-SDI-E, M32100T3-SDI-E or M32100T5-SDI-E.  
z When using with the M32100T-SDI-E or M32170T-SDI, separately available M3T-PTC-CNV is required.  
z When connecting to the M32100T-SDI-E or M32170T-SDI, connect the both cables for connecting the emulator,  
the SDI MCU control interface cable (10-pin) and the SDI trace interface cable (20-pin).  
z When using this product connecting to the M32100T-SDI-E, M32170T-SDI or M32100T2-SDI-E, do not change  
the MCU operating voltage.  
z For the precautions for the combination of the emulator, refer to the user’s manual of each emulator.  
Cautions for Differences between MCUs and This Product:  
z For debugging, as the M32192F8VWG (1MB internal Flash ROM) on the M32186T2-PTC is used, be careful about  
the difference of the internal memory size.  
zWhen the clock select switch is set to the “SOCKET” side, the oscillation occurs by itself, be careful about the  
difference of the resistance and the capacitor.  
z The capacitive load of the all lines of the MCU will increase depending on wirings and connectors. Use the part  
whose timing is critical after checking it works properly.  
Cautions to Be Taken for This Product:  
z When connecting the YQPACK144SD, be sure to use the included YQ-GUIDE’s.  
z We cannot accept any request for repair.  
z For purchasing the NQPACK144SD, YQPACK144SD and HQPACK144SD contact the following:  
Tokyo Eletech Corporation  
z For inquiries about the product or the contents of this manual, contact your local distributor.  
Renesas Tools Homepage  
(6/6)  
 

QSC Audio Portable Speaker MD FP122 66 User Guide
Rheem Water Heater HE45 160 User Guide
RocketFish Switch RF NBSKHBP User Guide
Rosewill Computer Drive RCW608 User Guide
RuggedCom Computer Hardware RX1501 User Guide
Samsung Camera Lens EXT85NB User Guide
Sansui Flat Panel Television HDLCD1900A User Guide
Sanyo Network Card POA LN01 User Guide
Savin All in One Printer 4035e User Guide
Sears Treadmill 831294880 User Guide