Renesas Computer Hardware H8S 2138 Series User Guide

H8S/2138 Series  
TQFP-80C  
User System Interface Cable  
(HS2138ECN61H)  
for E6000 Emulator  
User’s Manual  
HS2138ECN61HE(C)  
 
Preface  
Thank you for purchasing this user system interface cable (HS2138ECN61H) for the Renesas’s  
original microcomputer H8S/2138 series.  
The HS2138ECN61H is a user system interface cable that connects an H8S/2148, H8S/2138,  
H8S/2128 series E6000 emulator (HS2148EPI61H; hereinafter referred to as the emulator) to the IC  
socket for a TQFP-80C package (package code: TFP-80C) for the H8S/2138 series MCU on the  
user system.  
i
 
Contents  
Section 1 Configuration....................................................................................1  
Section 2 Connection Procedures......................................................................4  
2.1 Connecting User System Interface Cable to Emulator Station .........................................4  
2.2 Connecting User System Interface Cable to User System ................................................5  
2.2.1 Installing IC Socket .............................................................................................5  
2.2.2 Soldering IC Socket.............................................................................................5  
2.2.3 Inserting Cable Head ...........................................................................................5  
2.2.4 Fastening Cable Head ..........................................................................................6  
2.2.5 Connecting Cable Body to Cable Head ...............................................................8  
2.3 Recommended Dimensions for User System Mount Pad .................................................9  
2.4 Dimensions for User System Interface Cable Head..........................................................10  
2.5 Resulting Dimensions after Connecting User System Interface Cable.............................11  
Section 3 Installing the MCU to the User System.............................................12  
Section 4 Verifying Operation...........................................................................14  
Section 5 Notice ................................................................................................15  
ii  
 
Section 1 Configuration  
CAUTION  
Use an IC149-080-058-B51 socket (manufactured by  
YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-80C  
package IC socket on the user system.  
Figure 1 shows the configuration of the HS2138ECN61H user system interface cable for the  
TFP-80C package.  
1
 
To emulator station  
Cable body  
Screws (M2.6 x 12 mm)  
with flat washers  
Screws (M2.6 x 8 mm)  
with flat washers  
(for fastening cable head)  
Socket cover  
Cable head  
IC socket  
User system  
Figure 1 HS2138ECN61H User System Interface Cable  
2
 
Table 1 lists the HS2138ECN61H components. Please make sure you have all of these components  
when unpacking.  
Table 1  
HS2138ECN61H Components  
No. Component  
Quantity  
Remarks  
1
2
3
4
5
6
Cable body  
1
1
1
1
4
4
Includes flat cable  
Cable head  
IC socket  
For the TFP-80C package  
Socket cover  
For installing an TFP-80C packaged MCU  
For fastening cable head (with four flat washers)  
Screws (M2.6 x 12 mm)  
Screws (M2.6 x 8 mm)  
For installing an TFP-80C packaged MCU (with  
four flat washers)  
7
Documentation  
1
User’s manual for HS2138ECN61H (this manual)  
3
 
Section 2 Connection Procedures  
Connecting User System Interface Cable to Emulator Station  
WARNING  
2.1  
Always switch OFF the user system and the emulator  
product before the USER SYSTEM INTERFACE CABLE  
is connected to or removed from any part. Before connecting,  
make sure that pin 1 on both sides are correctly aligned. Failure to  
do so will damage the user system and the emulator product or will  
result in PERSONAL INJURY. The USER PROGRAM will be  
LOST.  
To connect the cable body to the emulator station, follow the instructions below.  
1. Make sure the user system and emulator station are turned off.  
2. After making sure the direction of the cable body connector is correct, firmly insert the cable  
body connector into the emulator station socket (figure 2).  
Emulator station  
0
0
0
6
E
Cable body  
User system interface cable  
Figure 2 Connecting User System Interface Cable to Emulator Station  
4
 
2.2  
Connecting User System Interface Cable to User System  
WARNING  
Always switch OFF the user system and the emulator  
product before the USER SYSTEM INTERFACE CABLE  
is connected to or removed from any part. Before connecting,  
make sure that pin 1 on both sides are correctly aligned. Failure to  
do so will damage the user system and the emulator product or will  
result in PERSONAL INJURY. The USER PROGRAM will be  
LOST.  
To connect the cable head to the user system, follow the instructions below.  
2.2.1 Installing IC Socket  
After checking the location of pin 1 on the IC socket, apply epoxy resin adhesive to the bottom of  
the IC socket for an TFP-80C package, and fasten it to the user system before soldering.  
2.2.2  
Soldering IC Socket  
After fastening, solder the IC socket for an TFP-80C package to the user system. Be sure to  
completely solder the leads so that the solder slops gently over the leads and forms solder fillets.  
(Use slightly more solder than the MCU.)  
2.2.3  
Inserting Cable Head  
CAUTION  
Check the location of pin 1 before inserting.  
Align pin 1 on the IC socket for an TFP-80C package on the user system with pin 1 on the user  
system interface cable head, and insert the user system interface cable head into the IC socket on the  
user system, as shown in figure 3.  
5
 
2.2.4  
Fastening Cable Head  
CAUTION  
1. Use a Phillips-type screwdriver whose head matches  
the screw head.  
2. The tightening torque must be 0.294 N•m or less.  
If the applied torque cannot be accurately measured,  
stop tightening when the force required to turn the screw  
becomes significantly greater than that needed when first  
tightening. If a screw is tightened too much, the screw  
head may break or an IC socket contact error may be caused  
by a crack in the IC socket solder.  
3. If the emulator does not operate correctly, cracks might  
have occurred in the solder. Check conduction with  
a tester and re-solder the IC socket if necessary.  
Fasten the user system interface cable head to the IC socket for an TFP-80C package on the user  
system with the four screws (M2.6 x 12 mm; with four flat washers) provided. Each screw should  
be tightened a little at a time, alternating between screws on opposing corners. Take special care,  
such as manually securing the IC socket soldered area, to prevent the soldered IC socket from being  
damaged by overtightening the screws or twisting the components.  
6
 
Screws (M2.6 x 12 mm), flat washer  
Cable head  
Pin 1  
IC socket  
(IC149-080-058-B51 manufactured by  
YAMAICHI ELECTRONICS Co. Ltd.)  
User system  
Figure 3 Connecting User System Interface Cable to User System  
7
 
2.2.5  
Connecting Cable Body to Cable Head  
Connect the cable body to the cable head.  
Cable body  
Removing  
Push the remove jig  
Remove jig  
Cable head  
User system  
Figure 4 Fastening Cable Body  
8
 
2.3  
Recommended Dimensions for User System Mount Pad  
Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system with  
an IC socket for an TFP-80C package (IC149-080-058-B51: manufactured by YAMAICHI  
ELECTRONICS Co., Ltd.). Note that the dimensions in figure 5 are somewhat different from those  
of the actual chip's mount pad.  
15.10 (min.)  
11.80 (max.)  
0.50 19 = 9.50 0.05  
0.50 0.05  
0.30 0.05  
Unit: mm  
Figure 5 Recommended Dimensions for Mount Pad  
9
 
2.4  
Dimensions for User System Interface Cable Head  
The dimensions for the user system interface cable head are shown in figure 6.  
Unit: mm  
Tolerance: –0.5 mm  
Figure 6 Dimensions for User System Interface Cable Head  
10  
 
2.5  
Resulting Dimensions after Connecting User System Interface Cable  
The resulting dimensions, after connecting the user system interface cable head to the user system,  
are shown in figure 7.  
Cable head  
IC socket  
(IC149-080-058-B51  
manufactured by  
YAMAICHI ELECTRONICS Co. Ltd.)  
User system  
Unit: mm  
Tolerance: –0.5 mm  
Figure 7 Resulting Dimensions after Connecting User System Interface Cable  
11  
 
Section 3 Installing the MCU to the User System  
CAUTION  
1. Check the location of pin 1 before inserting.  
2. Use a Phillips-type screwdriver whose head matches  
the screw head.  
3. The tightening torque must be 0.294 N•m or less.  
If the applied torque cannot be accurately measured,  
stop tightening when the force required to turn the screw  
becomes significantly greater than that needed when first  
tightening. If a screw is tightened too much, the screw  
head may break or an IC socket contact error may be caused  
by a crack in the IC socket solder.  
4. If the MCU does not operate correctly, cracks might have  
occurred in the solder. Check conduction with a tester  
and re-solder the IC socket if necessary.  
Check the location of pin 1 before inserting the MCU into the IC socket on the user system, as  
shown in figure 8. After inserting the MCU, fasten the socket cover with the provided four screws  
(M2.6 x 8 mm; with four flat washers). Take special care, such as manually securing the IC socket  
soldered area, to prevent the IC socket from being damaged by overtightening the screws or twisting  
the components.  
12  
 
Screws (M2.6 x 8 mm)  
with flat washers  
Socket cover  
MCU  
Pin 1  
IC socket  
(IC149-080-058-B51  
manufactured by  
YAMAICHI ELECTRONICS Co., Ltd.)  
User system  
Figure 8 Installing MCU to User System  
13  
 
Section 4 Verifying Operation  
1. When using the E6000 emulator (HS2148EPI61H) for the H8S/2148, H8S/2138, H8S/2128  
series, turn on the emulator according to the procedures described in the H8S Series E6000  
Emulator User's Manual (HS2000EPI61HE).  
2. Verify the user system interface cable connections by accessing the external memory and ports  
to check the bus states of the pins with the MEMORY_FILL command (emulator command). If  
an error is detected, recheck the soldered IC socket and the location of pin 1.  
3. The emulator connected to this user system interface cable supports two kinds of clock sources  
as the MCU clock: an emulator internal clock and an external clock on the user system. For  
details, refer to the H8S series E6000 Emulator User's Manual (HS2000EPI61HE).  
To use the emulator internal clock  
Select the clock in the emulator station as the system clock (φ), by using the CLOCK  
command (emulator command).  
To use the external clock on the user system  
Supply the external clock from the user system to the emulator. Connect a crystal oscillator  
to the EXTAL and XTAL terminals for the system clock (φ). Select the external clock as the  
system clock (φ), by using the CLOCK command (emulator command). For details, refer to  
section 22, Clock Pulse Generator, in the H8S/2138 Series, H8S/2134 Series Hardware  
Manual.  
Figure 9 shows the oscillator circuit on the user system interface cable.  
R1 1 M  
HCU04  
HCU04  
R2 270  
To E6000  
emulator  
EXTAL  
XTAL  
System clock  
Figure 9 Oscillator Circuit  
14  
 
Section 5 Notice  
1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable  
head before inserting the cable head into the user system IC socket.  
2. The dimensions of the recommended mount pad for the user system IC socket are different from  
those of the MCU.  
3. This user system interface cable is specifically designed for the HS2148EPI61H emulator. Do  
not use this cable with any other emulator station.  
4. To prevent breaking of wires in the cable body, do not place heavy or sharp metal objects on the  
user system interface cable.  
5. While the emulator station is connected to the user system with the user system interface cable,  
force must not be applied to the cable head. Place the emulator station, user system interface  
cable, and user system as shown in the example in figure 10.  
Place components so that the cable body and cable head are  
parallel to the user system.  
Cable  
Emulator station  
Cable head is parallel  
to emulator station  
Cable head is parallel  
to user system  
User system  
Figure 10 User System Interface Cable Location Example  
6. The JP1 short connector is used for testing. Do not remove the short pins that are inserted in the  
sides of pin 1 and pin 2.  
JP1  
Figure 11 JP1 Short Connector  
15  
 

Radica Games Games 75055 User Guide
Rangemaster Refrigerator U109200 03 User Guide
RedMax Trimmer CHT2301 User Guide
Regal Ware Kitchen Utensil K6740 User Guide
Runco Flat Panel Television PL 43DHD User Guide
Samsung Digital Photo Frame SPF 105P User Guide
Samsung Telephone dcs application User Guide
Sanyo Cordless Telephone CLT 5812 User Guide
Sanyo Microwave Oven EM C120 User Guide
Seagate Laptop ST320LM002 User Guide